This piece of craftsmanship is second to none. Special alloy, crafted to last, very precise. After thorough study on Beaters, this design is again reintroduced.

Can be used on:
Carpigiani
Coldelite
Promag
Cattabriga

These fans are highly reliable & available in various sizes, speeds, CFM. All possible electrical configurations available. Can be used in Soft Serve, Ice Cube, Beverage and many other Machines

The Beater Blades are meant for Carpigiani / Coldelite famous 3X Beaters. High Quality, injection moulded. Moulded from high scrapping quality plastic polymer.

One of the most popular part used by many Carpigiani users / distributors.

Can be used on all 3X Beaters of:
Carpigiani
Coldelite
Promag
Cattabriga

Famous Lawkim Beater Motor. Available from .75 HP till 5 HP.

220/50/1 & 415/50/3 specs. 60Hz option is also available. Rouged and reliable

This cyclic timer is a must in all electro-mechanical machines. You can have option of 5 Minutes / 1.5 Seconds if the Mix quality isn’t good. This time span restarts the machine in 5 minutes, much before the melt down of the Ice Cream inside the cylinder. This helps maintaining overrun & texture of the Ice Cream

The traditional 10 Minutes / 1.5 Second Cyclic Timer is also available.

It can be ordered in 24V, 110V & 220V, 50Hz or 60Hz

Our Gears are made from special Dairy Alloy which is the only approved alloy for such applications. Gears are of very high standards, precisely machined and ground. The inner bushes are precise, ground & further lapped to mirror finish for very low friction which results to low wear outs. These Gears can be used in non Self-Pasteurizing Machines.

These Gears are very popular amongst the Carpigiani users / distributors. They can be used in Carpigiani, Coldelite, Promag and Cattabriga Soft Serve – Soft Ice Cream Machines.

Rear Drive Hub (Driven). Very Precise – Ground – Hardened. Can be used in many Carpigiani / Coldelite Machines. We also undertake custom jobs for precise parts for Ice Cream Machines. Quality is Guaranteed.

Precise – Ground to perfection. High Grade 304 Stainless Steel. Can be used in most of the Carpigiani / Coldelite / Cattabriga / Promag Machines.

CE approved Over Load. Heavy duty, reliable, Manual & Automatic reset versions available. Can be used for Mono & Three Phase Equipment. 24V, 110V, 220V, 415V – 50/60Hz Coil available. Available in different Amperes settings.

Our Mix ‘R’ type Pump is unique piece of engineering. High quality, CNC Machined, new generation metrology, ground to perfection. All Pumps are individually tested. One of the most popular parts used by Carpigiani users / distributors.

This Complete ‘R’ type Pump comes with precise Gears, valves, springs & air regulation pipe. With the adjustable air regulating pipe, over-run can be adjusted from 40% to 85%. This helps getting maximum results out of various quality mixes.

So competitively priced that everyone would want to change the worn pump who till date had only option to repair Pumps or do with the worn out pumps.

Ideal investment as due to improved overrun, saving in mix is tremendous. Takes less then a season to recover this investment.

Can be used on:
Carpigiani
Coldelite
Promag
Cattabriga

Pump Shaft is precise, CNC machined, ground to perfection. Its surface is mirror finished, hard which reduces friction and lasts long.

New generation, wear resistance Stain Less Steel used. Very competitively priced and is popular amongst the Carpigiani users / distributors.

Can be used on :
(Always mention type of the shaft required)
Carpigiani
Coldlelite
Promag
Cattabrig

Rear Drive Pulley for Carpigiani / Coldelite / Cattabriga / Promag Machines

These Retrofit Beaters can be replaced with 2E or 3X Beaters. They give consistent overrun, rapid freezing. If replaced in the Tre/AP models, the performance zooms high. Very simple design and needs only blades to be changed unlike the 2E beaters which are to be replaced only.

Rotary Switch for Carpigiani Soft Serve Machines